ClimateMaster NB Series Manuel d'instructions télécharger pdf

INSTALLATION INSTRUCTIONS

ENERGY RECOVERY VENTILATOR SERIES WB, WC, WD, WE, WF, & WG

97B0042N05

Rev.: 15 May, 2015

Installation Instructions For Energy Recovery Wheel (Fixed)

For Stand Alone Over/Under Indoor Application

Energy recovery COMPONENT certiﬁ ed to the ARI Air-to-

Air Energy Recovery Ventilation Equipment Certiﬁ cation

Program in accordance with ARI Standard 1060-2000.

Actual performance in packaged equipment may vary.

ETL Certiﬁ ed per UL 1995 and CSA 22.2

Inspection

Upon receipt of shipment at the job site, carefully check the

shipment against the bill of lading. Make sure all units have

been received. Inspect the carton or crating housing of each

Rooftop Unit and inspect each unit for damage. Assure that

the carrier makes proper notation of any shortages or damage

on all copies of the freight bill and that he completes a Carrier

Inspection Report. Concealed damage not discovered during

unloading must be reported to the carrier within 15 days of

receipt of shipment. NOTE: It is the responsibility of the

purchaser to ﬁ le all necessary claims with the carrier.

Storage

Upon the arrival of equipment at the job site, immediately store

units in a clean, dry area. Do not stack units. Do not remove

equipment from pallets until equipment is required for

installation.

Unit Protection

Cover rooftop units on the job site. Cap the open ends of pipes.

In areas where painting, plastering, rooﬁ ng, or the spraying of

ﬁ reproof material has not been completed, all due precautions

must be taken to avoid physical damage to the units and

contamination by foreign material. Physical damage and

contamination may prevent proper start-up and may result

in costly equipment cleanup.

Application

Field supplied balancing dampers in duct are recommended.

Recovery Wheel Mode

The Recovery Wheel mode is accomplished by two blowers

providing continuous exhaust of stale indoor air and

replacement by equal amount of outdoor air. Energy recovery

is achieved by slowly rotating the energy recovery wheel within

the cassette frame work. In winter, the ERV adsorbs heat

and moisture from the exhaust air stream during one half of a

complete rotation and gives them back to the cold, drier intake

air supply during the other half rotation. In summer, the process

is automatically reversed. Heat and moisture are absorbed

from incoming fresh air supply and transferred to the exhaust

air stream. This process allows outdoor air ventilation rates

to be increased by factors of three or more without additional

energy penalty or increase in size of heating or air conditioning

systems.

Rigging Unit For Lifting

1. Maximum weight 300-1200 lbs. See Physical Data Table.

2. Remove crating.

3. All panels must be in place for rigging.

4. Remove barometric exhaust hood from door marked ﬁ lter

access. Install barometric exhaust hood over exhaust blower

outlet.

5. Forklift channels must be removed from the base of

ERV.

6. Position unit and provide service access to ERV control

access door and wheel.

7. Duct work should be installed into roof curb before installing

ERV on curb.

8. Roof curb gasket must be applied to all top surfaces of the

curb.

9. Position unit on roof curb and provide service access to ERV

control access door and wheel.

 CAUTION! 

CAUTION! Danger of sharp metallic edges. Can cause

injury. Take care when servicing unit to avoid accidental

contact with sharp edges.

 WARNING! 

WARNING! Electric shock hazard. Can cause injury or death.

Before attempting to perform any service or maintenance,

turn the electrical power to unit OFF at disconnect switch(es).

Unit may have multiple power supplies.

 WARNING! 

WARNING! To avoid equipment damage, do not use these

units as a source of heat during the construction process.

The mechanical components and ﬁ lters used in these units

will quickly become clogged with construction dirt and debris

which may cause system damage.

 WARNING! 

WARNING! The installation of water-source heat pumps and

all associated components, parts, and accessories which

make up the installation shall be in accordance with the

regulations of ALL authorities having jurisdiction and MUST

conform to all applicable codes. It is the responsibility of

the installing contractor to determine and comply with ALL

applicable codes, regulations and ANSI/NFPA No. 70

1 2 3 4 5 6 ... 15 16

Résumé du contenu

Page 1 -  WARNING! 

INSTALLATION INSTRUCTIONSENERGY RECOVERY VENTILATOR SERIES WB, WC, WD, WE, WF, & WG97B0042N05Rev.: 15 May, 2015Installation Instructions For Energ

Page 2

CLIMATEMASTER WATER-SOURCE HEAT PUMPSW (ERV) SeriesRev.: 15 May, 201510ClimateMaster Water-Source Heat PumpsERV UNIT WIRING DIAGRAM208- 230/460/575V (

Page 3

THE SMART SOLUTION FOR ENERGY EFFICIENCYW (ERV) SeriesRev.: 15 May, 201511climatemaster.comMist Eliminator Filter in Intake Hood (1.5HP)External Stati

Page 4

CLIMATEMASTER WATER-SOURCE HEAT PUMPSW (ERV) SeriesRev.: 15 May, 201512ClimateMaster Water-Source Heat PumpsMist Eliminator Filter in Intake Hood (3HP

Page 5

THE SMART SOLUTION FOR ENERGY EFFICIENCYW (ERV) SeriesRev.: 15 May, 201513climatemaster.comMist Eliminator Filter in Intake Hood (5HP)External Static

Page 6

CLIMATEMASTER WATER-SOURCE HEAT PUMPSW (ERV) SeriesRev.: 15 May, 201514ClimateMaster Water-Source Heat PumpsCLIMATE MASTER, INC.LIMITED EXPRESS WARRAN

Page 7

THE SMART SOLUTION FOR ENERGY EFFICIENCYW (ERV) SeriesRev.: 15 May, 201515climatemaster.comNotes

Page 8

CLIMATEMASTER WATER-SOURCE HEAT PUMPSW (ERV) SeriesRev.: 15 May, 201516ClimateMaster Water-Source Heat PumpsRevision History*97B0042N05*97B0042N05Clim

Page 9

CLIMATEMASTER WATER-SOURCE HEAT PUMPSW (ERV) SeriesRev.: 15 May, 20152ClimateMaster Water-Source Heat PumpsThis Page Intentionally Left Blank

Page 10 - W (ERV) Series

THE SMART SOLUTION FOR ENERGY EFFICIENCYW (ERV) SeriesRev.: 15 May, 20153climatemaster.comInstallation1. Attach duct work to duct ﬂ anges on ERV.2.

Page 11

CLIMATEMASTER WATER-SOURCE HEAT PUMPSW (ERV) SeriesRev.: 15 May, 20154ClimateMaster Water-Source Heat Pumpstimes that of the sensible heat load and in

Page 12

THE SMART SOLUTION FOR ENERGY EFFICIENCYW (ERV) SeriesRev.: 15 May, 20155climatemaster.comload conditions.1. Disconnect main power to unit before mak

Page 13

CLIMATEMASTER WATER-SOURCE HEAT PUMPSW (ERV) SeriesRev.: 15 May, 20156ClimateMaster Water-Source Heat PumpsEXHAUST AIRFRESH AIRRETURN AIRTREATED AIRFe

Page 14 - *LC083*

THE SMART SOLUTION FOR ENERGY EFFICIENCYW (ERV) SeriesRev.: 15 May, 20157climatemaster.comNotes:1. Remove jumper to install field optional low ambient

Page 15

CLIMATEMASTER WATER-SOURCE HEAT PUMPSW (ERV) SeriesRev.: 15 May, 20158ClimateMaster Water-Source Heat PumpsNotes:1. Remove jumper to install field opt

Page 16 - *97B0042N05*

THE SMART SOLUTION FOR ENERGY EFFICIENCYW (ERV) SeriesRev.: 15 May, 20159climatemaster.comERV UNIT WIRING DIAGRAMNotes:1. Remove jumper to install fie

Commentaires sur ces manuels

Pas de commentaire

ClimateMaster NB Series Manuel d'instructions

Naviguer en ligne ou télécharger Manuel d'instructions pour Climatiseurs à système divisé ClimateMaster NB Series. ClimateMaster NB Series Instruction manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels